The Intepro ELR 9000 HP is an enhancement of the ELR 9000, offering a new wide ranging mains connection of 360V-528V and increased power density. A single 3U chassis houses 5kW, 10k, or 15kW.

These devices incorporate four common regulation modes: constant voltage, constant current, constant power and constant resistance. The FPGA based control circuit provides additional features, such as a function generator, a table-based regulation circuit for the simulation of non-linear internal resistance.

The energy recovery function converts the supplied DC energy into a synchronous sine current and feeds it back into the local grid. This eliminates the usual heat dissipation to a minimum and saves energy costs at the same time. The large color TFT touch panel offers a different and intuitive kind of manual operation, compared to other devices.

Response times for the control via analog or digital interfaces have been improved by the FPGA controlled hardware. In parallel operation of multiple devices, a master-slave bus is used to connect over 64 units in parallel for over 1MW.

Key Features of the ELR 9000 HP DC LOAD products:

  • Energy Recovery

    Recover supplied DC energy into local or public grid
  • Wide Ranging AC Mains

    Accepts 360-528 VAC, 2/3 Phase, 45-66 Hz
  • Function Generator

    User profiles, true function generator
  • Parallel Connection

    Master-slave bus for parallel connection
  • SCPI

    SCP command language supported
  • USB Connectivity

    Extra USB port on the front for USB stick
  • Input Currents

    Up to 510 A per chassis
  • Input Voltage

    Up to 1500 V
  • Expandable

    Up to 480kW or more
elr9000hpsm ELR 9000 HP DC LOAD - Intepro SystemsELR 9000 HP DC Load

Regenerative load back to the grid

The standard regenerative function converts the supplied DC energy into a synchronous sine wave current and feeds it back into the local or public grid. This eliminates the usual heat dissipation to a minimum and saves energy costs at the same time.

The large LCD touch panel offers a modern and intuitive user interface for controlling the four operating modes, Constant Voltage (CV), Constant Current (CC), Constant Power (CP) and Constant Resistance (CR). Response times for the control via analog or digital interfaces by the DSP controlled hardware are among the fastest in the industry. In parallel operation of multiple devices, a master-slave bus is used to connect the chassis to create a high power system where the actual values are totaled and the set values distributed.

Wide range of Voltage, Current, Wattage

The available voltage range portfolio for the ELR 9000 HP programmable load goes from models with 0…80 V DC up to models with 0…1500 V DC. Input currents up to 510 amps per chassis are also available. The series offers three power classes with 5 kW, 10 kW or 15 kW in a compact 3U package, which can be extended up to 480kW (or higher) in cabinets for a significantly higher total current. Please contact Intepro systems for higher power solutions.

 

eapc en terminal1 full

Operation (HMI)

Manual operation is done with a Gorilla glass touch panel, two rotary knobs and a push-button. The large color display shows all relevant set values and actual values at a glance.

The whole setup is also done with the human-machine interface, as well the configuration of functions (square, triangle, sine) etc. The display is multilingual (German, English, Russian, Chinese).

 

Share Bus

The “Share Bus” is an analog connection at the rear of the devices and is used to balance current across multiple similar units in parallel connection, such as with loads of this series and series ELR 9000.

It can also be used to build a two-quadrants system in connection with our PSI 9000, PS 9000 and PSB 9000 Series DC Supplies. This system is dedicated for testing purposes using the source-sink principle.

Battery Test & MPP Tracking

For purposes of testing all kinds of batteries, such as for example constant current or constant resistance discharging, the devices offer a battery test mode. This mode shows extra values for elapsed testing time and consumed capacity (Ah). For more detailed setup, there is also an adjustable threshold to stop the battery test on low battery voltage, as well an adjustable maximum test period.

In order to simulate a solar inverter, the devices feature a function called “MPP tracking”, which is used to track and find the MPP (maximum power point) of the connected solar panel.

Remote Control & Connectivity

As for remote control, there are by default two interface ports (1x analog, 1x USB) available on the rear of the devices, which can also be extended by optional, pluggable and retrofittable, digital interface modules (dedicated slot).

Alternatively to the interface modules slot, all models can be equipped with option 3W (see below), which then offers 1x GPIB/IEEE, 1x USB and 1x Analog on the rear side of the device.

For the implementation into the LabView IDE we offer ready-to-use components (VIs) to be used with USB, RS232, GPIB and Ethernet. Other IDEs and interfaces may be supported upon request.

Windows users can profit from the free software “Power Control”. It offers a feature called “Sequencing”, where the device is controlled through a semi-automatic table in CSV format. This table represents a simple test procedure and can be created and edited in MS Excel or other CSV editors and then imported into the software tool.

This software also allows for the control of up to 20 units at once with an optional feature called “Multi Control” (licensed, not free of charge).

eapc en terminal1 full

 

elr9000 3u visio rear

About us

Intepro Systems is a Power Systems manufacture with over 35 years experience in the field.

Downloads

Overview Brochure 1
Get to know Intepro Systems!
Product Downloads 25
A comprehensive list of our online literature.
Energy Savings ROI Calculators 4
These Energy Savings ROI Calculators will help show you how Intepro can help you start saving today.

Contacts

  Email us at: Sales@inteproate.com

  (714) 953-2686

  (714) 953-2686

14662-E Franklin Avenue
Tustin, CA 92780

usa ELR 9000 HP DC LOAD - Intepro Systems

Intepro Systems America, LP

14662-E Franklin Avenue
Tustin, CA 92780
Call: 714-953-2686

uk ELR 9000 HP DC LOAD - Intepro Systems

Intepro UK Ltd.

9 Lakeside Business Park
Swan Lane, Sandhurst Berkshire
GU47 9DN / UK
Call: 44 012 5287 5600

ireland ELR 9000 HP DC LOAD - Intepro Systems

Intepro Systems Ireland Limited

Lonsdale Road
National Technology Park Limerick / Ireland
Call: 353 61 33 22 33

china ELR 9000 HP DC LOAD - Intepro Systems

Intepro Power Electronics (Shenzhen) Co., Ltd

No.828, Block 7,
Fourth Industrial Area
Nanyou, Nashan District
Shenzhen, China 518052
Tel: 0086 755 86500020